PCS SimpleWorx Sunrise Sunset Timer (SST)

Description

With a built-in astronomical clock, the SimpleWorx Sunrise Sunset Timer allows you to put one plug-in 120VAC device on one of 10 pre-programmed daily schedules. The connected device is also remotely controllable with up to eight SimpleWorx transmitters and locally controllable with the timer's manual override button.
10 Preset Schedules
#1:
On: SUNRISE, Off: SUNSET
#2:
On: SUNSET -30 Min, Off: SUNRISE +30 Min
#3:
On: SUNSET, Off: MIDNIGHT
#4:
On: SUNSET, Off: 10:00 PM
#5:
On: SUNSET, Off: 2:00 AM
#6:
On: SUNSET, Off: MIDNIGHT
On: SUNRISE -30 Min, Off: SUNRISE
#7:
On: SUNSET, Off: MIDNIGHT
On: SUNRISE -60 Min, Off: SUNRISE
#8:
On: SUNSET, Off: MIDNIGHT
On: 6:00 AM, Off: SUNRISE +30 Min
#9:
On: SUNSET, Off: 10:00 PM
On: SUNRISE -60 Min, Off: SUNRISE +30 Min
#10:
On: SUNSET, Off: 10:00 PM
On: SUNRISE -30 Min, Off: SUNRISE +30 Min
Every day, the timer calculates the appropriate times for SUNSET and SUNRISE settings, giving you precise scheduled control over the connected load. The timer's broad astronomic options cover Northern and Southern latitudes from 0-60° and Eastern to Western Longitudes from 66-125° , as well as 135 and 165° for Alaska and Hawaii. The timer also automatically adjusts for Daylight Savings Time and Leap Year.
Calculates Daily Dusk/Dawn Times For
0-60° for North and South latitudes
66-125° East to West longitudes
135 and 165° for Alaska and Hawaii
The timer plugs into a power outlet, and your 120VAC device plugs into the timer. Programming your desired schedule is simple. It only takes the push of a button to choose the schedule and time zone, and to view location latitude and longitude as well as Daylight Savings Time.
Easily Setup and Review
Schedule
Time Zone
Daylight Savings Time
Latitude and Longitude
Time Clock Settings
The timer includes a 40 Amp relay capable of 100,000 relay cycles. This relay features an on-board temperature sensor that automatically turns off the timer at 185° F in order to prevent overheating failures. The sensor automatically resets the timer once it returns to 167° F. Any damage to the timer caused by overheating is protected by a 10-year warranty.
In the event of a power outage, the timer's non-volatile memory saves programming indefinitely. When power is restored, the timer resets to its last state. The timer's heavy duty 125mA battery also protects the factory set clock for 10 years.
Technical Details
Manufacturer Part #:
SST
UPC:
811976013747
Warranty:
5 Year
Electrical
Power Requirements:
Primary: 120 Volts AC, 50/60Hz Single Phase
Neutral Wire:
Required
Channels:
1
Switch Load Types:
Standard inductive loads up to 15A and incandescent loads up to 800W
Relay Lifetime:
100,000 on/off operations at full electronic ballast load
Max Load:
15 Amps at 120VAC 50/60 Hz
Standby Power Consumption:
<0.8 Watts
Environmental Conditions:
Outdoor Water Resistant Use Only
Temperature:
-40 to 140° F (-40 to 60° C)
Humidity:
10 to 90% RH (non-condensing)
Certifications:
Safety tested for USA and Canada ETL tested to UL508; UL-508-2010CSA C22.2 #14-2010
Operation
Status LED Modes:
Red = Operation Mode
Blinking Green = Link Mode
Blinking Red = In Programming Mode
Blinking Orange = In Re-Schedule Mode
Slowly Blinking Red = Temperature Protection is Activated
During Power Outage:
Retains all settings in Non-volatile EERPOM
Mechanical
Set Button:
Button
Mounting:
3-pin grounded outlet
Dimensions:
3(L) x 2(W) x 1.55(D) inches
Weight:
0.3 ounces
Warranty:
10 years
US Patent No.:
6,734,784; 6,784,790; 7,265,654; 7,688,183. U.S. and foreign patents may be pending.
Mode Descriptions
Normal:
Power Is applied to device
Link:
Press and Hold Button for > 6 seconds
Link Exit:
Tap while in LINK Mode
Programming Mode:
3 taps while in LINK Mode
Programming Mode Exit:
Hold Button for 3 sec. while in PROGRAMMING Mode
Review Mode:
3 taps while in NORMAL Mode
Re-Schedule Mode:
4 taps while in LINK Mode
Clock Review Mode:
8 taps while in NORMAL MODE
Signal Strength Mode:
6 taps while in NORMAL Mode
Noise Strength Mode:
7 taps while in NORMAL Mode
Factory Default:
10 taps while in LINK Mode
LED Indicator Status
Red:
Normal Mode Power Applied
Blinking Red:
In Programming Mode
Blinking Green:
Link Mode
Blinking Orange:
In Re-Schedule Mode
Solid Green:
Transmitting a SPC Message
Dark/Green:
Test Mode
Pulses Green 1-16X:
Same Phase/ Signal Strength Display Mode of a Receiver
Pulses Red 1-16X:
Opposite Phase / Signal Strength Display Mode of a Receiver
Pulses Orange 1-16x:
Relative Noise Strength at Receiver
Blinks Red 10x:
Indicates that device has been factory defaulted
Slowly Blinking Red:
Temperature Protection is Activated